Technical data
Composition, density & standards
Reference data for every grade listed on this site: UNS composition limits, density, nearest EN designation, typical uses and commonly referenced standards.

Reference
Grade data by material
Copper offers very high electrical and thermal conductivity, excellent ductility and good corrosion resistance. Grades differ mainly in oxygen and phosphorus content, which decides how they behave when brazed, welded or used in electrical service.
| UNS | Alloy | Composition (wt %) | Density g/cm³ | Nearest EN | Typical uses |
|---|---|---|---|---|---|
| C10100 | Oxygen-free electronic (OFE) copper | Cu 99.99 min; O 0.0005 max | 8.94 | CW009A (Cu-OFE) | Vacuum devices; semiconductor and electronic parts; high-conductivity conductors; waveguides |
| C10200 | Oxygen-free (OFHC) copper | Cu 99.95 min; O 0.001 max | 8.94 | CW008A (Cu-OF) | Bus bars and conductors; vacuum and cryogenic equipment; brazed and welded assemblies; glass-to-metal seals |
| C11000 | Electrolytic tough-pitch (ETP) copper | Cu 99.90 min | 8.89 | CW004A (Cu-ETP) | Bus bars and electrical conductors; terminals and contacts; rolled sheet and strip; roofing and gaskets; general fabrication |
| C12000 | Deoxidised low-residual-phosphorus (DLP) copper | Cu 99.90 min; P 0.004–0.012 | 8.94 | CW023A (Cu-DLP) | Plumbing and refrigeration tube; heat-exchanger tube; brazed and welded assemblies |
| C12200 | Deoxidised high-residual-phosphorus (DHP) copper | Cu 99.90 min; P 0.015–0.040 | 8.94 | CW024A (Cu-DHP) | Water and gas tube; air-conditioning and refrigeration (ACR) tube; heat exchangers and condensers; brazed fittings |
| C12500 | Fire-refined tough-pitch (FRTP) copper | Cu 99.88 min | 8.89 | – | General-purpose copper products; roofing and flashing; fabricated parts |
Brass is a copper-zinc alloy. Raising the zinc content increases strength; adding lead improves machinability; adding tin, aluminium or arsenic improves corrosion resistance in water and seawater.
| UNS | Alloy | Composition (wt %) | Density g/cm³ | Nearest EN | Typical uses |
|---|---|---|---|---|---|
| C26000 | Cartridge brass (70/30) | Cu 68.5–71.5; Pb 0.07 max; Fe 0.05 max; Zn Remainder | 8.53 | CW505L (CuZn30) | Deep-drawn and stamped parts; radiator cores and tanks; fasteners; hardware; electrical terminals |
| C27000 | Yellow brass (65/35) | Cu 63.0–68.5; Pb 0.10 max; Fe 0.07 max; Zn Remainder | 8.47 | – | Rivets and screws; cold-headed and formed parts; hardware |
| C27200 | Yellow brass (63/37) | Cu 62.0–65.0; Pb 0.07 max; Fe 0.07 max; Zn Remainder | 8.44 | CW507L (CuZn37) | Rivets and screws; cold-headed parts; hardware; tube |
| C33000 | Low-leaded brass (tube grade) | Cu 65.0–68.0; Pb 0.25–0.7; Fe 0.07 max; Zn Remainder | 8.5 | – | Plumbing and pump tube; liners; hardware |
| C44300 | Admiralty brass (arsenical) | Cu 70.0–73.0; Sn 0.8–1.2; As 0.02–0.06; Pb 0.07 max; Fe 0.06 max; Zn Remainder | 8.53 | CW706R (CuZn28Sn1As) | Condenser and heat-exchanger tubes; evaporators; water service |
| C46400 | Naval brass (60/39/1) | Cu 59.0–62.0; Sn 0.5–1.0; Pb 0.20 max; Fe 0.10 max; Zn Remainder | 8.41 | – | Marine hardware; propeller shafts; valve stems; rivets; condenser plates; welding rod |
| C68700 | Aluminium brass (arsenical) | Cu 76.0–79.0; Al 1.8–2.5; As 0.02–0.06; Pb 0.07 max; Fe 0.06 max; Zn Remainder | 8.33 | CW702R (CuZn20Al2As) | Condenser, evaporator and heat-exchanger tubes; seawater and desalination service |
| C35300 | High-leaded brass (62/2) | Cu 60.0–63.0; Pb 1.5–2.5; Fe 0.15 max; Zn Remainder | 8.5 | – | Clock and instrument parts; gears; machined components; fittings |
| C36000 | Free-cutting brass | Cu 60.0–63.0; Pb 2.5–3.7; Fe 0.35 max; Zn Remainder | 8.5 | CW603N (CuZn36Pb3) | Screw-machine products; fittings and valve parts; gears; fasteners; general machined components |
| C37700 | Forging brass (60/2) | Cu 58.0–61.0; Pb 1.5–2.5; Fe 0.30 max; Zn Remainder | 8.44 | CW617N (CuZn40Pb2) | Hot-forged parts; valve bodies; plumbing fittings; hardware |
| C46200 | High-tensile naval brass | Cu 62.0–65.0; Sn 0.5–1.0; Pb 0.20 max; Fe 0.10 max; Zn Remainder | 8.41 | – | Marine hardware; shafts; valve stems; fasteners; condenser plates |
| C48200 | Naval brass, medium leaded | Cu 59.0–62.0; Sn 0.5–1.0; Pb 0.4–1.0; Fe 0.10 max; Zn Remainder | 8.44 | – | Machined marine hardware; shafts; valve stems; fasteners |
| C48500 | Naval brass, high leaded | Cu 59.0–62.0; Sn 0.5–1.0; Pb 1.3–2.2; Fe 0.10 max; Zn Remainder | 8.44 | – | Machined marine hardware; shafts; valve stems; fasteners; nuts and bolts |
| C26800 | Yellow brass (66/34) | Cu 64.0–68.5; Pb 0.15 max; Fe 0.05 max; Zn Remainder | 8.47 | – | Stamped and formed parts; hardware; reflectors; decorative components |
| C28000 | Muntz metal (60/40) | Cu 59.0–63.0; Pb 0.30 max; Fe 0.07 max; Zn Remainder | 8.39 | CW509L (CuZn40) | Condenser plates and tubesheets; architectural and marine hardware; bolts; hot-forged parts |
| C83600 | Leaded red brass (85-5-5-5), cast | Cu 84.0–86.0; Sn 4.0–6.0; Pb 4.0–6.0; Zn 4.0–6.0; Ni 1.0 max; Fe 0.30 max | 8.8 | – | Valves; pump bodies and impellers; fittings; general castings |
Bronzes are copper alloys with tin, aluminium or silicon as the main addition. They are chosen for strength, wear resistance and corrosion resistance, especially in bearings, marine hardware and valves.
| UNS | Alloy | Composition (wt %) | Density g/cm³ | Nearest EN | Typical uses |
|---|---|---|---|---|---|
| C22000 | Commercial bronze (90/10) | Cu 89.0–91.0; Pb 0.05 max; Fe 0.05 max; Zn Remainder | 8.8 | – | Architectural and decorative hardware; jewellery; fasteners; electrical terminals |
| C51000 | Phosphor bronze 5 % (A) | Sn 4.2–5.8; P 0.03–0.35; Pb 0.05 max; Fe 0.10 max; Zn 0.30 max; Cu Remainder | 8.86 | CW450K (CuSn5) | Springs; bellows; electrical contacts; fasteners; bearings; diaphragms |
| C52100 | Phosphor bronze 8 % (C) | Sn 7.0–9.0; P 0.03–0.35; Pb 0.05 max; Fe 0.10 max; Zn 0.20 max; Cu Remainder | 8.8 | CW453K (CuSn8) | Heavy-duty bearings; springs; gears; diaphragms; fasteners |
| C61400 | Aluminium bronze (D) | Al 6.0–8.0; Fe 1.5–3.5; Mn 1.0 max; Zn 0.20 max; Cu Remainder | 7.89 | – | Heavy-duty wear parts; bearings and bushings; corrosion-resistant fasteners; marine and process hardware |
| C63000 | Nickel-aluminium bronze | Al 9.0–11.0; Ni 4.0–5.5; Fe 2.0–4.0; Mn 1.5 max; Si 0.25 max; Zn 0.30 max; Cu Remainder | 7.58 | CW307G (CuAl10Ni5Fe4) | Marine fittings and shafts; pump and valve parts; gears; bearings; wear plates |
| C90500 | Gunmetal (tin bronze 88-10-2), cast | Cu 86.0–89.0; Sn 9.0–11.0; Zn 1.0–3.0; Pb 0.30 max; Ni 1.0 max; Fe 0.20 max | 8.72 | – | Gears; bearings and bushings; valves; steam fittings |
| C95400 | Aluminium bronze, cast | Cu 83.0 min; Al 10.0–11.5; Fe 3.0–5.0; Ni 1.5 max; Mn 0.50 max | 7.45 | – | Bearings; gears; valve seats and guides; pump parts; heavy-duty wear parts |
| C95800 | Nickel-aluminium bronze, cast | Cu 79.0 min; Al 8.5–9.5; Ni 4.0–5.0; Fe 3.5–4.5; Mn 0.8–1.5; Si 0.10 max | 7.58 | – | Marine propellers; pump casings and impellers; valve parts; shipboard castings |
| C52400 | Phosphor bronze 10 % (D) | Sn 9.0–11.0; P 0.03–0.35; Pb 0.05 max; Fe 0.10 max; Zn 0.20 max; Cu Remainder | 8.78 | – | Heavy-duty bearings and bushings; gears; wear plates; springs |
| C54400 | Free-cutting phosphor bronze (4/4/4) | Sn 3.5–4.5; Pb 3.5–4.5; Zn 1.5–4.5; P 0.01–0.50; Fe 0.10 max; Cu Remainder | 8.88 | – | Bushings; bearings; gears; thrust washers; screw-machine parts |
| C65500 | High-silicon bronze (A) | Si 2.8–3.8; Mn 0.50–1.3; Zn 1.5 max; Fe 0.8 max; Ni 0.6 max; Pb 0.05 max; Cu Remainder | 8.53 | CW116C (CuSi3Mn1) | Marine hardware; chemical equipment; fasteners; welded tanks; pole-line hardware |
| C67500 | Manganese bronze (A) | Cu 57.0–60.0; Fe 0.8–2.0; Sn 0.5–1.5; Mn 0.05–0.50; Pb 0.20 max; Zn Remainder | 8.36 | – | Marine fittings; valve stems; shafts; clutch discs; bolts |
| C92200 | Leaded tin bronze (88-6-1½-4½), cast | Cu 86.0–90.0; Sn 5.5–6.5; Pb 1.0–2.0; Zn 3.0–5.0; Ni 1.0 max; Fe 0.25 max | 8.64 | – | Valves; fittings; pump bodies; steam, water and marine service |
| C93200 | Bearing bronze (83-7-7-3), cast | Cu 81.0–85.0; Sn 6.3–7.5; Pb 6.0–8.0; Zn 2.0–4.0; Ni 1.0 max; Fe 0.20 max; Sb 0.35 max | 8.86 | – | Bearings; bushings; thrust washers; general bearing applications |
Technical data is general reference information (commonly published UNS and ASTM ranges), not a Melta Alloys test certificate. Always confirm against the governing standard and your material test certificate. Nearest EN designations are approximate.
Standards
Commonly referenced standards by product form
| Product form | Copper | Brass | Bronze |
|---|---|---|---|
| Pipes & Tubes | ASTM B75/B75M – seamless tube ASTM B88 – seamless water tube ASTM B280 – ACR tube ASTM B111 – condenser and heat-exchanger tube | ASTM B135 – seamless brass tube ASTM B111 – condenser and heat-exchanger tube ASTM B543 – welded tube | ASTM B111 – tube (applicable alloys) ASTM B271 – centrifugal castings ASTM B505 – continuous castings |
| Coils | ASTM B280 – ACR tube (coils) ASTM B68/B68M – bright-annealed tube ASTM B88 – water tube supplied in coils | – | – |
| Round Bars & Rods | ASTM B187/B187M – bar, bus bar, rod and shapes ASTM B133 – rod, bar and shapes | ASTM B16/B16M – free-cutting rod, bar and shapes ASTM B21/B21M – naval brass rod, bar and shapes ASTM B453 – leaded-brass rod, bar and shapes for hot forging | ASTM B139 – phosphor bronze rod, bar and shapes ASTM B150 – aluminium bronze rod, bar and shapes ASTM B98 – silicon bronze rod, bar and shapes ASTM B138 – manganese bronze rod, bar and shapes ASTM B505 – continuous-cast bar |
| Flat Bars | ASTM B187/B187M – bar, bus bar, rod and shapes ASTM B133 – rod, bar and shapes | ASTM B16/B16M – free-cutting rod, bar and shapes ASTM B21/B21M – naval brass rod, bar and shapes ASTM B453 – leaded-brass rod, bar and shapes for hot forging | ASTM B139 – phosphor bronze rod, bar and shapes ASTM B150 – aluminium bronze rod, bar and shapes ASTM B98 – silicon bronze rod, bar and shapes ASTM B138 – manganese bronze rod, bar and shapes ASTM B505 – continuous-cast bar |
| Square Bars | ASTM B187/B187M – bar, bus bar, rod and shapes ASTM B133 – rod, bar and shapes | ASTM B16/B16M – free-cutting rod, bar and shapes ASTM B21/B21M – naval brass rod, bar and shapes ASTM B453 – leaded-brass rod, bar and shapes for hot forging | ASTM B139 – phosphor bronze rod, bar and shapes ASTM B150 – aluminium bronze rod, bar and shapes ASTM B98 – silicon bronze rod, bar and shapes ASTM B138 – manganese bronze rod, bar and shapes ASTM B505 – continuous-cast bar |
| Hex Bars | ASTM B187/B187M – bar, bus bar, rod and shapes ASTM B133 – rod, bar and shapes | ASTM B16/B16M – free-cutting rod, bar and shapes ASTM B21/B21M – naval brass rod, bar and shapes ASTM B453 – leaded-brass rod, bar and shapes for hot forging | ASTM B139 – phosphor bronze rod, bar and shapes ASTM B150 – aluminium bronze rod, bar and shapes ASTM B98 – silicon bronze rod, bar and shapes ASTM B138 – manganese bronze rod, bar and shapes ASTM B505 – continuous-cast bar |
| Busbars | ASTM B187/B187M – bar, bus bar, rod and shapes | – | – |
| Plates & Sheets | ASTM B152/B152M – sheet, strip, plate and rolled bar | ASTM B36/B36M – plate, sheet, strip and rolled bar ASTM B19 – cartridge brass sheet, strip and plate ASTM B171 – condenser and heat-exchanger plate | ASTM B103/B103M – phosphor bronze plate, sheet and strip ASTM B96/B96M – silicon bronze plate, sheet and strip ASTM B169 – aluminium bronze sheet, strip and rolled bar |
| Buttweld Fittings | Dimensions and tolerances per customer standard or drawing | – | Dimensions and tolerances per customer standard or drawing |
| Forged Fittings | ASTM B124/B124M – forging rod, bar and shapes ASTM B283 – die forgings (hot-pressed) | – | ASTM B124/B124M – forging rod, bar and shapes ASTM B283 – die forgings (hot-pressed) |
| Threaded Fittings | ASME B16.15 – cast copper-alloy threaded fittings ASME B1.20.1 – pipe threads, general purpose | – | ASME B16.15 – cast copper-alloy threaded fittings ASME B1.20.1 – pipe threads, general purpose |
| Socket-Weld Fittings | Dimensions and tolerances per customer standard or drawing | – | Dimensions and tolerances per customer standard or drawing |
| Flanges | ASME B16.24 – cast copper-alloy pipe flanges and flanged fittings Other dimensions per customer standard or drawing | ASME B16.24 – cast copper-alloy pipe flanges and flanged fittings Other dimensions per customer standard or drawing | ASME B16.24 – cast copper-alloy pipe flanges and flanged fittings Other dimensions per customer standard or drawing |
| Stub Ends & Collars | Dimensions and tolerances per customer standard or drawing | Dimensions and tolerances per customer standard or drawing | Dimensions and tolerances per customer standard or drawing |
| Tube Fittings | ASME B16.26 – cast copper-alloy fittings for flared copper tubes Other dimensions per customer drawing | ASME B16.26 – cast copper-alloy fittings for flared copper tubes Other dimensions per customer drawing | ASME B16.26 – cast copper-alloy fittings for flared copper tubes Other dimensions per customer drawing |
| Fasteners | ASTM F468 – nonferrous bolts, screws and studs ASTM F467 – nonferrous nuts ASME B18.2.1 / B18.2.2 – dimensions | ASTM F468 – nonferrous bolts, screws and studs ASTM F467 – nonferrous nuts ASME B18.2.1 / B18.2.2 – dimensions | ASTM F468 – nonferrous bolts, screws and studs ASTM F467 – nonferrous nuts ASME B18.2.1 / B18.2.2 – dimensions |
| Stud & Threaded Rods | ASTM F468 – nonferrous bolts, screws and studs ASME B1.1 – unified inch screw threads | ASTM F468 – nonferrous bolts, screws and studs ASME B1.1 – unified inch screw threads | ASTM F468 – nonferrous bolts, screws and studs ASME B1.1 – unified inch screw threads |
| Welding Rods | AWS A5.7 – copper and copper-alloy bare welding rods and electrodes | AWS A5.7 – copper and copper-alloy bare welding rods and electrodes | AWS A5.7 – copper and copper-alloy bare welding rods and electrodes |
| Wires | ASTM B1 – hard-drawn wire ASTM B2 – medium-hard-drawn wire ASTM B3 – soft or annealed wire | ASTM B134 – brass wire | ASTM B159 – phosphor bronze wire |
| Foils | Dimensions and tolerances per customer standard or drawing | Dimensions and tolerances per customer standard or drawing | Dimensions and tolerances per customer standard or drawing |
| Strips | ASTM B152/B152M | ASTM B36/B36M | ASTM B103/B103M |
| Compression Fittings | ASME B16.26 – flared-tube fittings (where applicable) Other dimensions per customer drawing | ASME B16.26 – flared-tube fittings (where applicable) Other dimensions per customer drawing | ASME B16.26 – flared-tube fittings (where applicable) Other dimensions per customer drawing |
| Gaskets | Dimensions and tolerances per customer standard or drawing | Dimensions and tolerances per customer standard or drawing | Dimensions and tolerances per customer standard or drawing |
| Fittings | – | ASME B16.15 – cast copper-alloy threaded fittings ASME B16.18 / B16.22 – solder-joint fittings | – |
Commonly referenced standards for each product form; confirm exact coverage per enquiry. "–" means the form is not in the current list for that material.
Guide
Reading UNS numbers
| UNS range | Family |
|---|---|
| C10000–C15999 | Coppers and high-copper alloys |
| C20000–C49999 | Brasses (copper-zinc, with lead or tin variants) |
| C50000–C52999 | Phosphor bronzes (copper-tin) |
| C60000–C69999 | Aluminium bronzes, silicon bronzes and other copper-zinc alloys |
| C70000–C79999 | Copper-nickels and nickel silvers |
| C80000–C99999 | Cast coppers, brasses and bronzes |
Some trade names do not match the chemistry – for example commercial bronze (C22000) and manganese bronze (C67500) are copper-zinc alloys. Rely on the UNS number.
Need a quotation?
Send your grade, size, quantity and destination country, and we will come back to you.
